Understanding Plumbing Basics is Crucial for Installing a Bathtub
Understanding Plumbing Basics is Crucial for Installing a Bathtub
Blog Article
On this page down the page you can locate more high-quality data about Installing A Bathtub.
Mounting a bath tub isn't specifically rocket science, however it does need strong plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably difficult project. If the old tub is readily obtainable, the task can relocate immediately; if you have to open a wall surface to eliminate the old bathtub and position the brand-new tub, the task is a lot harder. In either instance, the job is within a house handyman's skills, although you will certainly need a helper to vacate the old bathtub and also embeded in the new one. Ensure you have actually certified on your own for the job and also are comfortable attempting it. Rather than hiring a service provider to take control of a halfway-completed project, it is far better to take into consideration using one prior to you start. Possibilities are you might require a specialist plumber to make tube links.
This post will certainly aid you mount a new bathtub in your washroom if you have already purchased a brand-new tub and also do not need to alter the plan of your previous water pipelines.
Your tools and also product checklist should comprise the following:
Getting ready for the Installation
To start with, the sustaining structure provided with the bathroom must be fitted (if called for) according to the maker's instructions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is also practical to fit a sustaining plate under the taps device to avoid stress on the tub.
Fit the flexible tap connectors to the bottom of both taps making use of 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its last placement.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, then the first thing you need to do is separate the water supply. After doing so, activate the faucets to drain any kind of water staying in the system. The procedure of removing the existing taps can be quite problematic as a result of the limited gain access to that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a towel all set for the continuing to be water that will come from the pipelines. As soon as the supply pipelines have actually been eliminated, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Before carrying on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Using both wooden boards under its feet, position the tub in the needed setting. The wooden boards are useful in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the level and readjusting the feet on the bath tub till the spirit level checks out degree.
To install taps, fit all-time low of the furthest adaptable tap port to the suitable supply pipe by making a compression sign up with; then do the very same for the other faucet.
Activate the water and also inspect all joints as well as brand-new pipework for leakages and also tighten them if required. Fill the bath tub as well as likewise examine the overflow electrical outlet and also the regular outlet for leakages.
Finally, repair the bath paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the bath tub ought to wait till the tub has actually been made use of a minimum of when as this will certainly settle it into its final placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in location between the faucet as well as the sink. Safeguard the tap in place with the producer given backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular tap ports. The previous kind needs to be connected to the faucet ends first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bath meets the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to split a stiff seal, causing the water to penetrate the wall between the bath and also the tiling, leading to difficulties with moisture as well as feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to constantly load the bathtub with water before securing, to permit the movement experienced when the tub remains in use. The sealant can fracture relatively early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise quickly offered on the market. It is a good idea to fit the ceramic tiles making use of waterproof or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that write-up about Installing A Bathtub from a good friend on our other site. Enjoyed our blog posting? Please share it. Let others discover it. I treasure reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
High-quality emergency response guaranteed. Report this page